Python Clamp
The first true clamp designed for hobby penis enlargement (PE) work. Gone are the days of hand exercises you can’t master, fussing with padding, not having the right size starting girth, using cable clamps not designed for PE work, trying to maintain erections or poor erection quality, and above all…the frustration of not gaining because you couldn’t figure out how to make clamping work! (Patent Pending)
Assembly Instructions
Operation Instructions
​
WARNING:
-Any numbness, tingling, excess coldness, or color changes to blue/black should not be ignored and are signs to release air pressure and remove the device as soon as possible. Restore circulation before continuing to use product
​
1. Bulb MUST be attached at all times to function, do not remove the hose and bulb from the clamp. Make sure the knob is set to the OFF (left, counter-clockwise position) and all air has left the device.
​
2. Be partly or fully soft/flaccid to insert into the clamp. You can use soapy water to aid with lubrication for insertion. Using lotions may cause slippage during operation.
​
3. If uncircumcised (uncut), be sure the foreskin is covering the head (glans) and insert it into the opening. The head will pop out of the foreskin on the other side of the clamp opening. If circumcised, use two fingers to compress and pull the head through the clamp opening.
​
4. Slide the device all the way down to the shaft base, resting at the bottom.
​
5. Gently turn the knob to the ON (right, clockwise position) to close the air valve. Do not overtighten the knob as it can damage the air valve.
​
6. If using a vacuum pump, place the included pump cylinder seal on top of the clamp and center it on the clamp. Next, place the pump cylinder on top of the clamp seal, and make sure the clamp, seal, and cylinder are centered with each other.
​
7. Slightly pump the clamp's air bulb to form a seal at the base.
​
8. Become erect by use of stimulation or pump (set to 5 Hg). Full erect for shock loading, or approximately 80% erect (still floppy) for clamped squeezes or overall expansion work.
​
9. Gently squeeze the clamp's air bulb to increase pressure until a surface tension on the penis is felt, becoming a slightly uncomfortable expansion sensation as the penis chambers are pushed to their expansion limits. DO NOT continue to add pressure if a stretched expansion feeling is felt at lower pressure levels.
NEVER pump to maximum pressure! If a bubble begins to form in the white sleeve, the device is beyond its limit and can fail (pop) if pressure is increased further...!!! Release some air to lower air pressure to safer levels.
​
10. Set a timer (5 minutes maximum) and hold in you preferred sitting/standing position, slightly increasing clamp pressure as required to maintain the desired expanded sensation. Typical adjustment to pressure setting is every 1-2 minutes. Do not adjust unless pressure loss is felt. Any tingling, numbness, coldness, or change in color to blue and/or black should not be ignored and is a sign to release air pressure on the device and remove if needed.
​
11. At the 5-minute mark, turn the clamp knob to the off (left) position and pressure should immediately drop.
​
12. Leave the device on your penis. If using a pump, remove the cylinder and leave the clamp on. Massage the shaft and head to restore color and circulation.
​
13. Repeat the setup procedure above, cycling between exercise and rest for up to 1 hour on a session day.
​
14 To remove the device, be flaccid as possible. Apply soapy water around the shaft to slide the device off. Remember to wash your device to avoid bacteria growth and avoid urinary tract infections.
​
15. Shock loading: Clamping sessions are suggested to be done for 1-2 sets of 5 minutes each before wearing a length device to shock load the tissues.
​
16. Girth sessions: Done every other day to help preserve erection quality. Increasing workout duration past 1 hour of 5-minute sets or continued daily use without rest days can negatively impact erection quality.
Clamp Insert Installation
Sleeve Installation
Need more help?
Still need more help? Contact Meadu customer support for all of your operational questions. Please allow 2-3 business days for a response.